Để lại lời nhắn
Chúng tôi sẽ gọi lại cho bạn sớm!
Gửi đi
Mr.
Mr.
Bà.
được
Chúng tôi sẽ gọi lại cho bạn sớm!
được
Để lại lời nhắn
Chúng tôi sẽ gọi lại cho bạn sớm!
Gửi đi
Vui lòng để lại email chính xác và yêu cầu chi tiết (20-3.000 ký tự).
được
english
français
Deutsch
Italiano
Русский
Español
português
Nederlandse
ελληνικά
日本語
한국
العربية
हिन्दी
Türkçe
indonesia
tiếng Việt
ไทย
বাংলা
فارسی
polski
Trang chủ
Về Chúng Tôi
Hồ sơ công ty
Tham quan nhà máy
Kiểm soát chất lượng
Sản phẩm
Phanh báo chí
Phanh ép thủy lực CNC
Phanh ép kim loại
Máy cắt thủy lực
Máy phay rãnh CNC
Máy hàn cực nhẹ
Máy ép thủy lực
Cắt chém thủy lực
Nhấn công cụ phanh
Lưỡi cắt kim loại
Dây chuyền sản xuất cực nhẹ
Thợ sắt
Máy cán tấm
Máy tạo hình kim loại
Máy đột dập CNC
giải pháp
Tin tức
Liên hệ với chúng tôi
english
français
Deutsch
Italiano
Русский
Español
português
Nederlandse
ελληνικά
日本語
한국
العربية
हिन्दी
Türkçe
indonesia
tiếng Việt
ไทย
বাংলা
فارسی
polski
Trích dẫn
Trang chủ
Về Chúng Tôi
Hồ sơ công ty
Tham quan nhà máy
Kiểm soát chất lượng
Câu hỏi thường gặp
Sản phẩm
Phanh báo chí
Phanh ép thủy lực CNC
Phanh ép kim loại
Máy cắt thủy lực
Máy phay rãnh CNC
Máy hàn cực nhẹ
Máy ép thủy lực
Cắt chém thủy lực
Nhấn công cụ phanh
Lưỡi cắt kim loại
Dây chuyền sản xuất cực nhẹ
Thợ sắt
Máy cán tấm
Máy tạo hình kim loại
Máy đột dập CNC
giải pháp
Tin tức
Liên hệ với chúng tôi
Trích dẫn
Tin tức
Created with Pixso.
Trang chủ
Created with Pixso.
Tin tức
Why CNC Hydraulic Press Brake Bending Accuracy Changes After Installation and How to Diagnose It
The machine passed its factory test, was dismantled, shipped, reinstalled and now bends differently from the recorded result. Nothing is visibly damaged. Between the two measurements four conditions changed: the foundation, the residual stress state of the frame, the alignment of major components ...
11-06-2026
What Should Buyers Test During Factory Acceptance Testing of a 160T/4000 CNC Hydraulic Press Brake?
A 160T/4000 machine is the workhorse size in most fabrication shops, and the factory acceptance test is the last point at which a defect is somebody else's responsibility. The protocol below is deliberately measurement-based: every item produces a number that can be compared with the specification ...
11-06-2026
How to Prevent Cracking When Bending 304 Stainless Steel with a CNC Hydraulic Press Brake
304 stainless seldom fails in the middle of a bend. It fails at an outer edge, usually on the first piece after a material change, and the crack often runs only part of the way through the thickness. The mechanism is mechanical rather than a defect in the steel, which means it can be controlled with ...
11-06-2026
Mechanical vs Hydraulic Crowning: How to Verify Compensation Performance on a CNC Hydraulic Press Brake
Crowning is the one system on a press brake whose job is to deform the machine deliberately. The bed and upper beam deflect under load, and compensation pre-loads the bed upwards so that, at working tonnage, the gap along the length is uniform. Two technologies do this, and the practical question is ...
11-06-2026
Why Do CNC Hydraulic Press Brakes Lose Backgauge Position Accuracy During Multi-Bend Production?
A four-bend box that fits for the first twenty pieces and then runs out of square is usually a backgauge problem, not a bending problem. In multi-bend work the gauge is repositioned many times per part, so any lost motion, datum error or thermal growth appears once per move and accumulates across ...
11-06-2026
How to Calculate Off-Center Bending Loads and Prevent Frame Distortion in CNC Hydraulic Press Brakes
A 160 tonne machine is rated for 160 tonnes along the bed. A 300 mm wide bracket bent at the end of a 4000 mm bed applies its force over a fraction of that length, and the frame sees a moment the tonnage rating does not describe. The calculation takes two minutes and prevents a permanent loss of ...
11-06-2026
1
2
3
4
5
6
7
8
Liên hệ với chúng tôi
Gửi